i
Great product - but watch those hooks!
I feel confident these holders will support any keyboard up to about 25 pounds (about 10 kg) with no reinforcement.
The hooks on the end arrived a little loose on mine. No problem - just use an Allen key (not provided) to tighten them. They thread into a plastic insert which expands when tightened, to stay in place in the aluminum extrusion. I strongly recommend buyers check to make sure they are not loose. Just try to pull them out as hard as you can. If they move, push them back in and tighten.
Also, double-check the underside of your keyboard. On my Akai AX-60, the bottom is sloped toward the keyboard at the front, and the hooks are not long enough to safely prevent the keyboard from sliding off if it is sloped toward the player. The hooks are about 4-5 cm in length, but a length of 6.5 cm is required for the AX60. I also own a couple of older Korg keyboards with a similar slope on the underside, but I haven't tried them - I expect to encounter similar problems. For such keyboards, you must either set them up to be level, or replace the hooks - you could use wood, or aluminum bar stock (1/4" x 3/4") as I did.
The hooks on the end arrived a little loose on mine. No problem - just use an Allen key (not provided) to tighten them. They thread into a plastic insert which expands when tightened, to stay in place in the aluminum extrusion. I strongly recommend buyers check to make sure they are not loose. Just try to pull them out as hard as you can. If they move, push them back in and tighten.
Also, double-check the underside of your keyboard. On my Akai AX-60, the bottom is sloped toward the keyboard at the front, and the hooks are not long enough to safely prevent the keyboard from sliding off if it is sloped toward the player. The hooks are about 4-5 cm in length, but a length of 6.5 cm is required for the AX60. I also own a couple of older Korg keyboards with a similar slope on the underside, but I haven't tried them - I expect to encounter similar problems. For such keyboards, you must either set them up to be level, or replace the hooks - you could use wood, or aluminum bar stock (1/4" x 3/4") as I did.
1
0
Report
M
Versatile and qualitative.
Used to attach extra devices to the original keyboard holder.
Pros:
- Quality
- Lightness
- Easy mounting on the existing support, no need to disassemble it.
Cons:
- none
Pros:
- Quality
- Lightness
- Easy mounting on the existing support, no need to disassemble it.
Cons:
- none
2
0
Report
DK
Excellent Addition To My Jaspers 170-4-150-19B Rack
I bought 2 sets of these to add to my Jaspers 170-4-150-19B rack. They are super easy to instal (do read the leaflet so you get them the right way around!). They are constructed very well as are all the Jaspers parts I’ve seen. I like the versatility of the Jaspers System you can make the rack that you need by adding parts like these to a basic rack.
0
0
Report
H
Well made. Ideal fit.
Needed to get some kit - drum machine and bass sequencer - off my studio desk and onto the Jaspers stand - these do the job nicely. Perfect match on a D keyboard stand.
1
0
Report
F
Super easy upgrade
I needed a couple more arms for some drum machines but was apprehensive that I'd need to completely take apart my stand in it's current configuration. Turns out that installation was fast and easy and I didn't have to remove anything. Arms easily pop on to the current cross bar and lock in place.
Pros : They hold gear and don't fall off
Cons: These aren't distributed in the USA and shipping charges are steep.
Pros : They hold gear and don't fall off
Cons: These aren't distributed in the USA and shipping charges are steep.
0
0
Report
A
holds my wavestate and opsix perfectly
these fit perfect on the jaspers multistand I also purchased. My only regret is not getting three 40B, instead of one 40B and one 60B due to mis-measurement. But, larger still fits and distributes weight just as properly. These actually arrived first - so - nice and quickly dispatched. Thank you
0
0
Report
A
Valuable holders
I bought my holders as an edition to my Jaspers existing keyboard stand. They fit exactly my Jaspers stand and they're very easy to mount. Very robust, stable and solid build.
Great looking holders worth every cent.
Now my early eighties heavy duty synth of about 17kg is held by this great holders made in Germany. Thank you again Thomann and keep up the good job with quality equipment. Thumbs up.
Great looking holders worth every cent.
Now my early eighties heavy duty synth of about 17kg is held by this great holders made in Germany. Thank you again Thomann and keep up the good job with quality equipment. Thumbs up.
0
0
Report
R
Best in the biz
Does what it should. Great quality.
0
0
Report
K
Does the job
I have used other keyboard stands but found it hard to get hold of additions. Being able to purchase additional brackets for your equipment is why i purchased the Jaspers stand. The price reflects the quality. Easy to fix and adjust. Feels solid.👍
0
0
Report
L
Sturdy Built
Great product. Excellent for my Jaspers 3R keyboard stand. It holds my Moog Sub 37 very well.
0
0
Report