Harley Benton CLO-70ASR NAT AllSolid

To be honest I didn’t expect much for 299€, however Harley Benton have done an excellent job of producing a very playable solid wood acoustic guitar at this price point. The manufacturing and set up were pretty much spot on. I’ve had the guitar for a month or so now and it has been played every day, it stays in tune and it is very comfortable to play.
After two weeks I changed the original HB strings for a set of D’Addario 12-53 XS strings, not because the originals were bad just so that I could do a comparison. There was a difference, the D’Addario were fuller and gave a more rounded tone (to my ear) but it wasn’t really necessary the originals were fine. The one aspect that I see as a potential weakness is the tuners, they appear quite fragile, they’ll probably be fine and as I said previously, the guitar stayed in tune well.
All in all a great value guitar and very pleased with my purchase. I’ve added some additional dimensions of the guitar that I couldn’t find on the website, someone might find them useful.
Upper bout width: 290mm
Waist width: 244mm
Lower bout width: 395mm
Body length: 492mm
Depth of body at the top (neck joint): 97mm
Depth of body at the bottom: 115.5mm

Update February 2026: The lid did not survive its first winter. The soundboard split from the bridge down to the lower bout, and it looks like it had already been glued before (i.e. hidden factory defect). The tension causing the crack is probably what caused the weird resonance too - it still can't handle loud playing, but there's less distortion now.

I own a CLA-16S which sounds great, and there were no issues with the CLA-15M SolidWood I owned either, but this particular one seems to have been a dud.

Pros:
- Great body shape with nice punchy/woody sound
- The finishing is well above and beyond what you can expect at this price range
- I was fortunate with the aesthetics on my guitar, there are no knots or blemishes on the wood itself and the grain looks great.
- I don't like bound fretboards, but it perfectly matches the fretboard on my guitar so I didn't notice it until I did my first restring.
- The factory setup was fine. I had to turn the truss rod when I switched strings the first time, but once that was in place, the action was great without any further adjustments.
- The tuners work great.

With that out of the way, here are the cons:
- The nut is cut too deep, so it grips the strings. I replaced it with a tusq nut (which needed shimming because the tusq nut wasn't tall enough). Tuning stability is great after switching the nut, and since the first nut was otherwise cut so well, I didn't need to do any gradual adjustments, I just copied the factory nut straight up.
- The strings supplied with the guitar are terrible. It says on the product page they're .012 strings, but they felt like .010 strings.
- Supporting that notion, once I restrung the guitar with proper .012 strings, the softness of the neck was revealed. It completely bowed and I had to adjust the truss rod a lot. It feels like the truss rod isn't just stabilizing the neck, but completely supporting it. This piece of wood should not have been chosen for a steel-stringed guitar.

And finally the most important con: My specific guitar seems to have some issues with the sound board, and there are a lot of harsh harmonics and rattling when I play hard, almost as if the lid was cedar, and not spruce. I thought it was the strings first, but now after having tried three different brands and finally tying and waxing the ball ends but still having issues with distortion-like resonance, I don't see what else it can be, than the guitar itself.

Since wood grading is not completely haphazard, I think you can expect similar issues with your guitar.

If you're a quiet player, or you play with lighter gauge strings, this guitar is exemplary. It has the high-end response you usually don't get with plywood guitars in this price range, and the body shape is great for light strumming and soft picking.

If you're a harder playing guitarist or you like regular or medium string tensions... you could order a couple guitars of this make for the price of a more expensive guitar and hope for the best, or you could just straight up buy one of those more expensive guitars, or look elsewhere, like the budget offerings from Cort and Ibanez. Yamaha is a good option too if you have a guitar tech handy, and of course the other Harley Benton offerings with solid wood soundboards.

Bought this guitar after reading the specs and seeing the price. Solid spruce top and SOLID rosewood back and sides for £250! Incredible value. Guitar arrived in great condition, with a pleasingly low action. One criticism I would have is that it is instantly noticeable that the nut is not quite cut low enough - feels as if you have to press the strings down just a little bit more on the first fret than you should have to to get a clean chord sound. Speaking of strings, I’m a fan of 10s for acoustic. These come with 12s, which I’ve always found too stiff and difficult to play - it’s much easier to fret and bend the 10s (and I’m not good enough to notice subtle differences in the sound between 12s and 10s). Sound is very good to my ears for both finger picking and chord strumming. Overall, a beautiful looking guitar, with easy playability and a good tone. And it’s £250! Incredible.

Everything is well made, nicely succeed. Flawless finish, unpolluted.
I've upgraded the strings (D'daddario XS) and it sounds really good.

The only weak point is in the inside, in the left rib there's a kind of patch, made of some synthetic material, maybe installed from factory for electronics.
But for this model, doesn't need that. I've tried to remove it by hand without success. It is really hard attached to the wood, and I don't want to screw up the guitar.

Maybe this factory details need to be considered for better results in the future.